www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 o f 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hd f 433 m1 smd - 6 prepared checked approved ? d a t e 20 09 - 10 - 28 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 o f 9 ?? history record date spec . no . ?? part no . ??? customer no . modify content ? remark
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 o f 9 1. features ? high stability and reliability with good performance and no adjustment. ? low insertion loss and deep stop band attenuation for interfere nce. 2. electrical specification items rating unit input signal level 10 dbm dc permissive voltage 6 v dc storage temperature range - 40 ~ +8 5 electronic characteristics 2 - 1.typical frequency response
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 o f 9 2 - 2.electrical characteristics items test condition min typ max unit center frequency - - 433.92 - mhz insertion loss f o - 2. 4 3.2 db 433.78~434.06 mhz - 0. 2 2.0 db 433.74 ~ 434.10 mhz 0. 3 3.0 db amplitude ripple(p - p) 433.70 ~ 434.14 mhz 0 .5 6.0 db 3db bandwidth f o - 3db 0. 65 0. 72 0. 79 mhz 10.00~ 414.00 mhz 55 60 - db 414.00 ~ 423.50 mhz 42 55 - db 423.50 ~ 430.10 mhz 35 42 - db 430.10 ~ 432.20 mhz 22 28 - db 432.20 ~ 433.10 mhz 1 8 35 - db 434.92 ~ 440.30 mhz 18 27 - db 440 .30~ 451.40 mhz 30 35 - db 451.40 ~ 810 .00mhz 47 53 - db attenuation 810.00~2 500.00mhz 60 65 - db
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 o f 9 3. test circuit 4. dimension
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 o f 9 5. environmental characteristics 5 - 1 temperature cycling subject the d evice to a low temperature of - 4 0 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +8 0 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 2 - 2 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2 - 2 . 5 - 3 solderability submerge the device term inals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 2 - 2 . 5 - 4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2 - 2 . 5 - 5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 2 - 2 . 6. rema rk 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the componen t. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 7 . packing 7 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be pac ked properly not to be damaged during transportation and storage. 7 .2 reeling quantity 1000 pcs/reel 7??
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 o f 9 3000 pcs/reel 13?? 7 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications. 8 . tape specifications 8 .1 tensile strength of carrier tape: 4.4n/mm width 8 .2 top cover tape adhesion (see the below figure) (1) pu ll off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 o f 9 [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2] [unit:mm] a b c d e w t r
saw filter hd f433m1 s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 o f 9 ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
